Let’s face it, pool upkeep could be daunting. However on the subject of draining your Intex pool, you do not have to let the duty overwhelm you. With the best instruments and some easy steps, you possibly can successfully drain your pool with out problem. Whether or not you are making ready for the winter months or just must refresh your pool water, this information will give you all the mandatory data to make sure a profitable drainage course of.
Earlier than embarking on the drainage, it is important to find out probably the most appropriate drainage technique on your Intex pool. Relying in your pool dimension, location, and entry to water disposal choices, you possibly can select from two major strategies: utilizing a submersible pump or connecting a backyard hose to the drainage valve. This information will cowl each methods intimately, offering clear directions and useful tricks to make the method as clean as attainable.
As you proceed with the drainage, hold security on the forefront. Guarantee you could have a transparent and steady work space, put on acceptable clothes and gloves, and be cautious of any potential electrical hazards. Moreover, contemplate the impression of draining your pool on the encompassing surroundings and eliminate the water responsibly. By following the steps outlined on this information and adhering to security precautions, you possibly can confidently drain your Intex pool, leaving it prepared for its subsequent use or the dormant winter months.
Draining the Pool Water
Join the Backyard Hose
* Find the drain plug on the backside of the pool wall.
* Connect the backyard hose to the drain plug tightly.
* Make sure the hose is lengthy sufficient to achieve an appropriate drainage space.
Pump the Water Out
* Activate the water provide to create a suction impact.
* The water will start to empty out of the pool.
* If the water stream slows down, gently squeeze the hose to create a greater seal.
Monitor the Draining Course of
* Regulate the water degree because it drains.
* Cease the draining course of when the water is about 2-3 inches above the underside of the pool.
* Take away the drain plug and permit the remaining water to empty out naturally.
| Time | Quantity of Water Drained |
|---|---|
| First half-hour | Roughly 300 gallons |
| Subsequent half-hour | Roughly 200 gallons |
| Remaining time | Roughly 100 gallons |
Extra Ideas for Draining Intex Pool:
* Use a submerged pump for sooner drainage.
* If the drain plug is tough to take away, use a pair of pliers to softly loosen it.
* Elevate the pool barely by inserting it on a platform to enhance drainage.
* Keep away from draining the pool on uneven surfaces, as this could trigger pooling and injury to the pool liner.
Eradicating Water from the Filter System
1. Flip Off the Filter System and Water Provide
Unplug the filter system and shut the water provide to the pool. This prevents any additional water from coming into the filter whilst you’re draining it.
2. Disconnect the Filter Hoses
Take away the inlet and outlet hoses from the filter system. In case you have a sand filter, take out the multiport valve meeting as effectively. Place an empty bucket or container close by to gather any remaining water.
3. Drain the Water from the Filter
To empty the water from the filter, you could have a number of choices:
Gravity Drain: Open the handbook drain plug on the backside of the filter. Enable the water to empty naturally into the container. That is the simplest and commonest technique.
Pump Drain: Join a pump to the filter’s handbook drain plug. This technique means that you can pump out the water sooner and extra effectively.
Siphon Drain: Create a siphon by submerging one finish of a transparent hose within the filter’s water and the opposite finish within the container. The water will begin flowing as a result of vacuum created.
For sand filters, additionally comply with these steps:
| Step | Description |
|---|---|
| 1 | Take away the drain plug from the sand filter’s backside. |
| 2 | Place the filter’s drain plug within the container to gather the water. |
| 3 | Slowly activate the filter. |
| 4 | The water will begin draining out of the filter. |
Siphoning Water from the Pool
Step 1: Collect Supplies
Earlier than you begin, collect the mandatory supplies: a siphon hose (out there at most {hardware} shops), a bucket or bigger container, and a pair of pliers or wrench.
Step 2: Join the Siphon Hose
Connect one finish of the siphon hose to the bottom drain valve on the pool. The opposite finish needs to be submerged within the bucket or container.
Step 3: Prime the Siphon
To prime the siphon, fill the hose with water till it reaches the best level. Then, rapidly submerge the opposite finish within the bucket. Gravity will begin the water flowing, and the siphon will proceed to run so long as the hose stays submerged.
Step 4: Monitor the Draining Course of
Because the water drains, monitor its degree and regulate the siphon hose accordingly. Relying on the scale of the pool and the stream price, draining could take a number of hours. If the siphon stops working, verify for clogs or air bubbles within the hose.
Step 5: Drain the Remaining Water
As soon as many of the water has been drained, there could also be a small quantity remaining within the backside of the pool. This may be eliminated utilizing a submersible pump or by manually bailing it out with a bucket.
Utilizing a Pump to Drain
Utilizing a pump to empty your Intex pool is a comparatively straightforward and environment friendly technique. Listed below are the steps you will must comply with:
Gathering Your Supplies
Earlier than you start, you will want to assemble the next supplies:
- Submersible pump
- Backyard hose
- Bucket or different container
Setting Up the Pump
Place the submersible pump contained in the pool and join it to the backyard hose. The opposite finish of the hose needs to be positioned within the bucket or container the place you need the water to empty.
Priming the Pump
Most submersible pumps should be primed earlier than they’ll begin pumping water. To do that, fill the pump with water till it reaches the fill line. You might want to make use of a bucket to pour water into the pump.
Beginning the Pump
As soon as the pump is primed, you possibly can flip it on. It ought to begin pumping water instantly. If it would not, verify to make it possible for the pump is correctly linked to the hose and that the hose isn’t kinked.
Monitoring the Water Stage
Because the pump drains the water, you will want to observe the water degree within the pool. As soon as the water degree has dropped beneath the extent of the pump, you will must cease the pump and transfer it to a decrease location within the pool.
Extra Ideas
Listed below are a couple of further suggestions for draining your Intex pool utilizing a pump:
| Tip | Description |
|---|---|
| Use a high-capacity pump. | This may assist to empty the pool sooner. |
| Place the pump within the deepest a part of the pool. | This may assist to make sure that the pump is ready to drain your entire pool. |
| Preserve the pump working constantly. | This may assist to stop the pump from overheating. |
Troubleshooting Frequent Drainage Points
Downside: Water Circulation is Gradual
Examine the drain plug and the tip of the hose for any clogs. This could possibly be brought on by particles, leaves, or grime. If that’s the case, take away the obstruction and water will start to empty once more.
Downside: Pool Cowl is Obstructing the Drain
Take away the pool cowl and proceed draining. You may set up the duvet later as soon as the pool is empty.
Downside: Drain Hose is Kinked
Make sure that the drain hose is positioned correctly and never kinked or twisted. Straighten out the hose and take away any kinks to permit water to stream by way of.
Downside: Drain Plug is Not Securely Connected
Examine if the drain plug is absolutely inserted and correctly tightened. Tightening it’s going to create a seal and stop water from leaking.
Downside: Pool is Not Stage
Place a degree on the facet of the pool to find out if it is degree. If it isn’t, elevate the decrease finish to tilt the water in the direction of the drain.
Downside: Clogged Filter Cartridge
In case you have a filter pump, clear the filter cartridge. A clogged cartridge can cut back water stream and hinder drainage.
Downside: Drain Plug Will not Open
In uncommon instances, the drain plug could also be caught resulting from corrosion or particles. If you cannot open it manually, you could want to make use of pliers or a wrench. Keep away from over-tightening.
Downside: Drain Cap is Unfastened
Examine the drain cap on the pool wall. If it is unfastened, tighten it utilizing a screwdriver or wrench.
Downside: Gap in Drain Hose
Examine for any holes or tears within the drain hose. For those who discover any injury, exchange the hose with a brand new one.
Security Precautions
- Disconnect all electrical cords from the pump and filter.
- Make sure that the pool isn’t plugged into {an electrical} outlet.
- Put on gloves and eye safety when dealing with chemical compounds.
- Observe the producer’s directions for chemical utilization and disposal.
- Supervise youngsters always close to the pool.
- By no means drain the pool straight right into a sewer or storm drain.
- Use a hose or bucket to empty the water into a chosen space, reminiscent of a garden or backyard.
- Concentrate on any underground pipes or cables which may be buried close to the pool.
- If there’s any doubt concerning the security of draining the pool, contact a professional skilled.
- Extra Security Precautions for Utilizing a Sump Pump:
- Use a floor fault circuit interrupter (GFCI) to stop electrical shock.
- Make sure that the sump pump is linked to a separate electrical circuit.
- Examine the sump pump frequently to make sure that it’s functioning correctly.
- Preserve the sump pump space away from particles and obstructions.
- If the sump pump fails, unplug it and speak to a professional skilled for restore.
How To Drain Intex Pool
Draining an Intex pool is an easy course of that may be accomplished in a couple of steps. First, you will have to assemble the mandatory supplies, which embody a backyard hose, a submersible pump, and a bucket. After you have gathered your supplies, you possibly can start the draining course of.
To start, connect the backyard hose to the submersible pump. Then, place the submersible pump within the pool and switch it on. The pump will start to pump water out of the pool and into the backyard hose. As soon as the water degree has dropped beneath the extent of the pump, you possibly can flip off the pump and take away it from the pool.
Subsequent, you will have to make use of the bucket to bail out the remaining water from the pool. As soon as all the water has been faraway from the pool, you possibly can fold it up and retailer it away for future use.
Individuals Additionally Ask About How To Drain Intex Pool
What’s one of the best ways to empty an Intex pool?
One of the best ways to empty an Intex pool is to make use of a submersible pump. Submersible pumps are designed to pump water out of flooded areas, and they’re highly effective sufficient to empty a pool rapidly and effectively.
Can I exploit a backyard hose to empty an Intex pool?
Sure, you should use a backyard hose to empty an Intex pool. Nevertheless, it’s going to take longer to empty the pool utilizing a backyard hose than it’s going to utilizing a submersible pump.
How do I eliminate the water from my Intex pool?
One of the best ways to eliminate the water out of your Intex pool is to empty it right into a storm drain. For those who shouldn’t have entry to a storm drain, you may also drain the water right into a ditch or different low-lying space.
