Are you uninterested in having to modify between the bathe and bathtub manually? A diverter valve will help! This useful system permits you to simply change the circulate of water from the showerhead to the bathtub spout, and vice versa. Putting in a diverter valve is a comparatively easy challenge that may be accomplished in a number of hours. This is a step-by-step information that will help you get began.
Earlier than you start, you will want to collect a number of instruments and supplies. You may want a diverter valve (out there at most {hardware} shops), a wrench, a screwdriver, and a few Teflon tape. Upon getting all the pieces you want, you can begin the set up course of. Step one is to close off the water provide to your bathe. Subsequent, take away the showerhead by unscrewing it from the bathe arm. As soon as the showerhead is eliminated, you will must take away the outdated diverter valve. To do that, merely unscrew the valve from the bathe arm. Now, you are prepared to put in the brand new diverter valve. Begin by wrapping the threads of the valve with Teflon tape, then screw the valve onto the bathe arm.
As soon as the diverter valve is put in, you’ll be able to reattach the showerhead. Activate the water provide to your bathe, and verify for leaks. If there are not any leaks, you are all set! Now you can benefit from the comfort of a diverter valve in your bathe.
Putting in the New Diverter Valve
1. Take away the Previous Diverter Valve
Find the screws holding the outdated diverter valve in place and take away them. Gently pull the valve away from the pipe, taking care to not harm the threads.
2. Verify the Threads
Examine the threads on the pipe and the brand new diverter valve. Be sure that they’re clear and freed from particles. If vital, use a thread cleaner to take away any burrs or corrosion.
3. Apply Sealant
Apply a skinny layer of sealant to the threads of the brand new diverter valve. This may assist create a watertight seal.
4. Set up the Diverter Valve
Thread the brand new diverter valve onto the pipe by hand, guaranteeing it’s aligned appropriately. Tighten it additional utilizing a wrench, being cautious to not overtighten.
5. Set up the Deal with
Find the deal with on the brand new diverter valve and align it with the slot on the valve physique. Slide the deal with onto the valve and safe it by tightening the screw.
6. Reattach the Escutcheon
Take the escutcheon (the ornamental plate surrounding the valve) and align it over the valve physique. Safe it by tightening the screws. Be sure that the escutcheon matches snugly towards the wall.
Extra Particulars for Step 6:
– If the escutcheon doesn’t match flush towards the wall, you could want to make use of a spacer or washer to create a greater match.
– When tightening the escutcheon screws, keep away from overtightening, as this may harm the plate or the wall.
– If the escutcheon has a number of screws, tighten them in a star sample to make sure even strain distribution.
– As soon as the escutcheon is safe, verify for any gaps or leaks across the edge. If vital, apply extra sealant to seal any leaks.
Testing the Diverter Valve for Leaks
As soon as the diverter valve is put in, it is essential to check it for leaks. This may be sure that the valve is functioning correctly and that there are not any water leaks.
To check the diverter valve for leaks, observe these steps:
1. Activate the water provide to the bathe or tub.
2. Open the bathe or tub faucet and let the water run for a couple of minutes.
3. Verify for any leaks across the diverter valve. If there are any leaks, tighten the packing nut or substitute the O-ring.
4. Repeat steps 1-3 for the bathtub spout.
5. Flip off the water provide to the bathe or tub.
6. Verify for any leaks across the diverter valve. If there are any leaks, tighten the packing nut or substitute the O-ring.
7. If there are not any leaks, the diverter valve is put in and functioning correctly.
8. In case you are nonetheless experiencing leaks after following these steps, there could also be an issue with the diverter valve itself. On this case, you will have to switch the diverter valve.
| Leak Location | Doable Trigger | Answer |
|---|---|---|
| Across the diverter valve deal with | Unfastened packing nut | Tighten the packing nut |
| Across the diverter valve physique | Broken O-ring | Change the O-ring |
| Across the bathe or tub spout | Unfastened connection | Tighten the connection |
The way to Match a Diverter Valve
A diverter valve is a plumbing fixture that permits you to management the circulate of water between two completely different shops. This may be helpful for a wide range of functions, corresponding to diverting water from a showerhead to a tub spout, or from a kitchen sink to a dishwasher. Diverter valves are comparatively simple to put in, and may be performed in a number of easy steps.
Step 1: Collect your supplies.
You will have the next supplies to put in a diverter valve:
- Diverter valve
- Wrench
- Plumber’s tape
- Screwdriver
Step 2: Flip off the water provide.
Earlier than you start engaged on the diverter valve, you will need to flip off the water provide to the fixture. This may be performed by turning off the primary water valve in your house, or by turning off the person water valve for the fixture.
Step 3: Take away the outdated diverter valve.
As soon as the water provide is turned off, you’ll be able to take away the outdated diverter valve. To do that, merely use a wrench to unscrew the nuts that maintain the valve in place. As soon as the nuts are unfastened, you’ll be able to pull the valve off of the pipe.
Step 4: Set up the brand new diverter valve.
To put in the brand new diverter valve, merely reverse the steps that you just used to take away the outdated valve. First, apply a small quantity of plumber’s tape to the threads of the valve. Then, screw the valve onto the pipe. Lastly, tighten the nuts that maintain the valve in place.
Step 5: Activate the water provide.
As soon as the diverter valve is put in, you’ll be able to activate the water provide. Verify for leaks across the valve, and tighten the nuts as vital.
Step 6: Take a look at the diverter valve.
To check the diverter valve, merely activate the water and verify to ensure that the water is flowing to the right outlet. If the water is just not flowing to the right outlet, you could want to regulate the place of the valve.
Folks Additionally Ask
How do I do know if I want a diverter valve?
You could want a diverter valve if you wish to management the circulate of water between two completely different shops. For instance, you could want a diverter valve if you wish to divert water from a showerhead to a tub spout, or from a kitchen sink to a dishwasher.
What are the various kinds of diverter valves?
There are two principal sorts of diverter valves: push-pull diverter valves and lever diverter valves. Push-pull diverter valves are operated by pushing or pulling on a knob, whereas lever diverter valves are operated by transferring a lever up or down.
How do I select the precise diverter valve?
When selecting a diverter valve, you have to take into account the next elements:
- The kind of fixture you might be putting in the valve on
- The variety of shops you wish to management
- The circulate fee of the water
- The type of the valve
- The value of the valve
