Changing a heating aspect in a Samsung dryer can prevent the price of shopping for a brand new dryer or hiring an equipment restore technician. To switch the heating aspect, you will first want to assemble the mandatory instruments and supplies, together with a brand new heating aspect, screwdriver, and pliers. Upon getting the mandatory objects, observe these steps to exchange the heating aspect in your Samsung dryer.
First, unplug the dryer from the ability outlet and take away the again panel of the dryer. Subsequent, find the heating aspect and disconnect the wires which can be hooked up to it. Then, take away the previous heating aspect from the dryer. To put in the brand new heating aspect, merely insert it into the dryer and reconnect the wires. Lastly, change the again panel of the dryer and plug it again into the ability outlet. Your Samsung dryer ought to now be working correctly.
If you’re not assured in your potential to exchange the heating aspect your self, it’s best to contact a professional equipment restore technician. A certified technician will have the ability to shortly and safely change the heating aspect in your Samsung dryer and get it working correctly once more.
Security Precautions
Earlier than embarking on the duty of changing the heating aspect in your Samsung dryer, it’s crucial to prioritize your security. Electrical energy and heating parts can pose important dangers if correct precautions usually are not taken. To make sure a protected and profitable restore, meticulously adhere to the next security measures:
1. Disconnect the Energy Supply
The primary and most vital step is to disconnect {the electrical} provide to your dryer. That is a vital security measure to forestall any unintended electrical shocks or fires. Find the principle electrical panel in your house and swap off the circuit breaker or take away the fuse similar to the dryer. Confirm that the ability has certainly been disconnected by testing the dryer outlet with a voltage tester. Wait a couple of minutes to permit any residual electrical energy within the system to dissipate.
| Suggestions for Disconnecting the Energy Supply |
|---|
| – Establish the proper circuit breaker or fuse for the dryer. |
| – Swap off the corresponding circuit breaker or take away the fuse. |
| – Use a voltage tester to verify that the outlet is not receiving energy. |
| – Permit enough time for the residual electrical energy to dissipate. |
Collect Vital Instruments and Supplies
Earlier than embarking on the restore, it is essential to assemble the important instruments and supplies. Here is an in depth rundown of what you will want:
Supplies:
- New heating aspect
- Electrical tape
- Warmth-resistant gloves (non-compulsory)
Instruments:
| Software | Function |
|---|---|
| Phillips-head screwdriver | Take away the screws securing the entry panels and heating aspect |
| Torx screwdriver | Unscrew the bolts holding the heating aspect in place (some fashions) |
| Multimeter | Check the continuity of the heating aspect (non-compulsory) |
| Pliers (non-compulsory) | Tighten or loosen nuts or bolts |
| Protecting goggles (non-compulsory) | Defend eyes from free particles |
Further Supplies:
Whereas not strictly essential, sure supplies could make the restore course of smoother:
- Flashlight: Illuminate the work space, particularly in dimly lit areas
- Store towels or rags: Clear up any particles or spills
- Digicam: Doc the disassembly course of for simpler reassembly
- Warmth gun (non-compulsory): Soften previous adhesive or pace up evaporation of moisture
- Soldering iron (non-compulsory): Restore broken wires or safe new connections
Find and Take away the Rear Panel
Unplug the dryer and transfer it away from the wall.
For security functions, unplug your dryer from the ability outlet earlier than beginning any repairs. It will even be greatest to drag the dryer away from the wall to present your self ample house to work.
Find the screws holding the rear panel in place.
Figuring out the screws that maintain the rear panel of the dryer is essential. These screws are sometimes situated across the perimeter of the panel, and their place might differ barely relying on the dryer mannequin. Upon getting recognized the screws, proceed to the subsequent step.
Take away the screws and punctiliously carry off the rear panel.
Upon getting situated the screws, use a screwdriver to take away them. Watch out to not strip the screws or harm the rear panel when eradicating them. After eradicating all of the screws, fastidiously carry the rear panel off the dryer. Word that the rear panel could also be barely heavy, so remember to help it with one hand whereas eradicating the screws with the opposite.
Disconnect Present Heating Component
**Step 1: Unplug the Dryer**
Earlier than engaged on the dryer, disconnect it from the ability provide by unplugging it from the wall outlet.
**Step 2: Take away the Again Panel**
Find the screws on the again panel of the dryer and take away them utilizing a screwdriver. Rigorously carry and take away the again panel to show the interior parts.
**Step 3: Disconnect Wires**
Establish the 2 wires linked to the heating aspect terminals. Gently pull the wire connectors off the terminals. Make word of which wire goes to which terminal for future reference.
**Step 4: Take away the Heating Component**
The heating aspect is held in place by two screws or bolts. Use a wrench or socket to loosen and take away these fasteners. Rigorously slide the heating aspect out of its housing. Be aware of sharp edges and keep away from touching the aspect along with your naked arms.
| Screw/Bolt Location | Elimination Technique |
|---|---|
| High of the housing | Loosen with a wrench or socket |
| Backside of the housing | Take away with a wrench or socket |
**Step 5: Examine the Heating Component**
Visually examine the heating aspect for any harm or corrosion. If the aspect is broken, it would must be changed earlier than reassembling the dryer.
Take away Previous Heating Component
5. Disconnect the heating aspect from the ability provide.
| Kind of Dryer | Steps |
|---|---|
| Gasoline Dryer |
Shut off the gasoline provide to the dryer earlier than continuing. |
| Electrical Dryer |
Unplug the dryer from the ability outlet and switch off the circuit breaker or fuse for the dryer circuit |
6. Take away the screws that maintain the heating aspect in place.
7. Unclip the wire terminals from the heating aspect.
8. Pull the heating aspect out of the dryer.
Set up New Heating Component
Security Precautions
Earlier than starting any work, unplug your dryer and disconnect the ability supply. Make sure that the machine is cool to the contact.
Eradicating the Previous Heating Component
- Take away the entrance panel of the dryer by unscrewing the screws on the prime and pulling it ahead.
- Find the entry panel on the entrance of the dryer’s drum. Take away the screws and pull it open.
- Pull the previous heating aspect unit in the direction of you to disconnect the wires.
- Unplug the wires from {the electrical} terminals and take away the previous heating aspect.
Putting in the New Heating Component
- Insert the brand new heating aspect unit into the opening within the drum.
- Join the wires to {the electrical} terminals. Make sure that the connections are safe.
- Push the heating aspect unit again into place and safe it with the screws.
- Reattach the entry panel and the entrance panel of the dryer.
- Plug the dryer again into the ability outlet and switch it on to check the brand new heating aspect.
Suggestions for Troubleshooting
| Downside | Resolution |
|---|---|
| Dryer not heating | Test the ability provide. Examine the wires and connections to the heating aspect. Check the heating aspect with a multimeter. |
| Dryer overheating | Unplug the dryer and let it settle down. Clear the lint filter and exhaust vent. Test the thermostat and temperature sensor. |
Reconnect Electrical Wires
Now it is time to reconnect {the electrical} wires to the heating aspect. Make sure you match the wires to the proper terminals on the aspect. Usually, the crimson wire will hook up with the left terminal and the white wire will hook up with the correct terminal. Nonetheless, consult with your dryer’s particular wiring diagram to verify.
Tighten the screws on the terminals securely utilizing a screwdriver. Make sure that the wires are making good contact with the terminals to forestall any free connections that might trigger arcing or different electrical points.
As soon as the wires are linked, tuck them again into the insulation across the heating aspect. This can assist to guard the wires from warmth harm and hold the within of the dryer tidy.
Wiring Diagram
For fast reference, here’s a desk with a normal wiring diagram for many Samsung dryers:
| Wire Shade | Terminal |
|---|---|
| Pink | Left Terminal |
| White | Proper Terminal |
Once more, double-check your dryer’s particular wiring diagram to make sure accuracy earlier than making any connections.
Exchange Rear Panel
Now that the screws are eliminated, carry the rear panel up from the underside and pull it in the direction of you to detach it from the dryer. Watch out to not harm any wires or parts as you do that.
As soon as the rear panel is eliminated, you should have entry to the heating aspect. The heating aspect is situated on the backside of the dryer, behind the drum. It’s held in place by two screws.
Step 8: Take away the Heating Component’s Wiring
Earlier than eradicating the heating aspect, you must disconnect its wiring. The heating aspect has two wires linked to it: a black wire and a white wire. Use a pair of pliers to softly pull the wires off of the heating aspect’s terminals.
As soon as the wires are disconnected, you may take away the heating aspect. Use a screwdriver to take away the 2 screws that maintain the heating aspect in place. As soon as the screws are eliminated, the heating aspect will be pulled out of the dryer.
| Step 6: Find the Heating Component | The heating aspect is situated on the backside of the dryer, behind the drum. It’s held in place by two screws. |
| Step 7: Disconnect the Heating Component’s Wiring | Earlier than eradicating the heating aspect, you must disconnect its wiring. The heating aspect has two wires linked to it: a black wire and a white wire. Use a pair of pliers to softly pull the wires off of the heating aspect’s terminals. |
| Step 8: Take away the Heating Component | As soon as the wires are disconnected, you may take away the heating aspect. Use a screwdriver to take away the 2 screws that maintain the heating aspect in place. As soon as the screws are eliminated, the heating aspect will be pulled out of the dryer. |
As soon as the previous heating aspect is eliminated, you may change it with the brand new one. Insert the brand new heating aspect into the dryer and safe it with the 2 screws. Make sure you join the wires to the heating aspect’s terminals within the right order: black wire to black terminal, white wire to white terminal.
As soon as the brand new heating aspect is put in, you may reattach the rear panel to the dryer. Safe the rear panel with the screws that you just eliminated earlier.
Check the Dryer
Upon getting changed the heating aspect, you will need to take a look at the dryer to verify it’s working correctly. Listed below are the steps on tips on how to take a look at the dryer:
| Step | Motion |
|---|---|
| 1 | Be sure that the dryer is plugged into an outlet and that the ability swap is turned on. |
| 2 | Open the dryer door and place a moist towel inside. |
| 3 | Shut the dryer door and choose the “Regular” or “Timed Dry” cycle. |
| 4 | Press the “Begin” button to start out the dryer. |
| 5 | Let the dryer run for a couple of minutes to see if the towel will get heat. |
| 6 | If the towel will get heat, then the heating aspect is working correctly. |
| 7 | If the towel doesn’t get heat, then there could also be an issue with the heating aspect or different parts of the dryer. |
If you’re having issues along with your dryer, it’s best to contact a professional equipment restore technician for help.
Security Precautions Earlier than Beginning:
1. Unplug the dryer from the ability outlet and permit it to chill fully.
2. Put on gloves to guard your arms from sharp edges.
3. Collect all essential instruments and elements earlier than beginning.
Checking the Heating Component:
1. Take away the again panel of the dryer by unscrewing the screws across the perimeter.
2. Find the heating aspect, which is often an oblong metallic field with two wires linked to it.
3. Unplug the wires from the heating aspect utilizing needle-nose pliers.
Eradicating the Heating Component:
1. Unscrew the nuts holding the heating aspect in place.
2. Rigorously carry the heating aspect out of the dryer cupboard.
Putting in the New Heating Component:
1. Place the brand new heating aspect into the dryer cupboard.
2. Tighten the nuts holding the heating aspect in place.
3. Join the wires to the heating aspect.
Troubleshooting Suggestions
1. If the dryer nonetheless doesn’t warmth, examine the thermal fuse.
2. If the thermal fuse is blown, change it.
3. If the heating aspect shouldn’t be getting energy, examine the wiring.
4. If the wiring is broken, restore or change it.
5. If the dryer remains to be not heating, contact a professional equipment restore technician.
Further Troubleshooting Suggestions:
| Doable Trigger | Resolution |
|---|---|
| Free belt | Alter or change the belt |
| Vent blockage | Clear the dryer vent |
| Defective thermostat | Exchange the thermostat |
| Defective relay | Exchange the relay |
| Defective management board | Exchange the management board |
7. If the dryer is making a loud noise, examine the drum bearings.
8. If the drum bearings are worn, change them.
9. If the dryer is shaking excessively, examine the shock absorbers.
10. If the shock absorbers are worn, change them.
How one can Set up a Heating Component in a Samsung Dryer
Changing the heating aspect in a Samsung dryer is a comparatively easy job that may be accomplished in about an hour. Nonetheless, you will need to take security precautions and observe the directions fastidiously to keep away from harm or harm to the dryer.
Supplies wanted:
- New heating aspect
- Screwdriver
- Wrench
- Security glasses
- Gloves
Directions:
- Unplug the dryer from the ability outlet.
- Placed on security glasses and gloves.
- Take away the again panel of the dryer by unscrewing the screws that maintain it in place.
- Find the heating aspect, which is often situated on the backside of the dryer.
- Disconnect the wires from the heating aspect.
- Unscrew the bolts that maintain the heating aspect in place.
- Carry the heating aspect out of the dryer.
- Place the brand new heating aspect into the dryer.
- Screw within the bolts to safe the heating aspect in place.
- Join the wires to the heating aspect.
- Exchange the again panel of the dryer.
- Plug the dryer again into the ability outlet.
